
MasonrySaver
Safer Masonry Cleaner
- Cleans & Etches Concrete, Stone, Tile, & Other Natural Stone Surfaces
- Safer Alternative to Muriatic Acid: Contains a Special Additive That Reduces Fumes & Burns Normally Associated with Muriatic Acid
- Improves Adhesion of Sealers: Great for Use Before Painting or Sealing Concrete Driveways, Paver Patios, Sidewalks, Garage Floors, or Other Masonry & Concrete Surfaces (Requires Rinsing)
- Easy to Use & Easy to Clean Up with Soap & Water
Limitations: Do not use on limestone!
This product will dissolve limestone surfaces.

WARNING: This product can expose you to chemicals including 1,4-dioxane, which is known to the State of California to cause cancer, and ethylene glycol, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
FOR EXTERIOR USE ONLY
Coverage: 125 sq. ft. per gal
Cleanup: Soap & Water
Application Method: Pump-up Sprayer
For Use On: Concrete, brick, stone, sandstone, limestone, or any other naturally porous, untreated concrete or masonry surface.
VOC Content: <100 g/L
KEEP FROM FREEZING
DIRECTIONS FOR USE
SURFACE PREPARATION: IMPORTANT NOTES: Do not use MasonrySaver Safer Masonry Cleaner on limestone as the product will dissolve the limestone. Always test in an inconspicuous area to ensure desired results. Protect foliage and all applicable surrounding surfaces including wood, glass, aluminum, asphalt roofing, vinyl siding, and painted surfaces. Beware of wind drift.
APPLICATION
DILUTION: Dilute MasonrySaver Safer Masonry Cleaner 4:1 with water. For difficult to remove stains this product can be used full strength. Caution: When diluting product with water slowly add the product to the water while stirring. Never add water to the product.
- Brush surfaces to be cleaned with a stiff brush to remove loose particles.
- Wet all surfaces to be cleaned with liberal amounts of water.
- Flood the surface with MasonrySaver Safer Masonry Cleaner taking care that the product does not run down onto non-targeted areas.
- Using a stiff non-metal brush, scrub the area thoroughly, allowing the cleaning solution to remain on the area for three to five minutes.
- Completely rinse the treated area using a garden hose with adjustable nozzle, or pressure washer set at 400-600 psi. When rinsing use as much water as possible. To avoid streaking rinse from the bottom up. For severely stained areas it may be necessary to repeat the application of MasonrySaver Safer Masonry Cleaner.
PRECAUTIONS
DANGER: CAUSES SKIN BURNS & EYE DAMAGE. Contains a chemical that is suspected of causing adverse reproductive effects. Keep container closed. Wash hands thoroughly after handling. Do not take internally. The use of chemical splash gloves and a NIOSH approved respirator is highly recommended when using this product. Wear eye protection. Dispose of contents/container to comply with applicable local, national, and international regulations.
FIRST AID
IF INHALED: Remove to fresh air. Get medical attention if symptoms persist. SKIN CONTACT: Flush exposed skin immediately with large amount of water for 15 minutes. Get medical attention if irritation persists. Remove contaminated clothing and wash it before reuse. EYE CONTACT: Immediately flush with water for at least 15 minutes, holding eyelids open. Remove contact lenses, if present and easy to do after the first 5 minutes and then continue flushing. Get immediate medical attention. IF SWALLOWED: DO NOT induce vomiting. Rinse mouth with water. Never give anything by mouth to a person who is unconscious or drowsy. Get immediate medical attention. For additional information on this product, consult the product data sheet or SDS available at www.masonrysaver.com.
KEEP FROM FREEZING
7 Year Limited Warranty
Our recommendations for use of this product are based upon tests believed to be reliable. Since field conditions vary widely, the user must determine the suitability of the product for the particular use and specific method(s) of application. SaverSystems’ warrants that MasonrySaver All-Purpose Heavy-Duty Water Repellent will exhibit a water repellent effect on vertical surfaces for seven years from the date of application when properly applied according to label instructions and if minimum application requirements are met. This warranty does not cover pre-existent flaking, spalling, abrading, faulty construction and/or other defects which might erode treated surfaces. If water repellent fails to perform as specified, SaverSystems will furnish, as sole remedy, enough water repellent to correct the condition. This warranty does not include labor, or the cost of labor for the re-application of water repellent. SaverSystems shall not be liable for incidental or consequential damages resulting from any breach of this warranty and fitness for use. Some states do not allow the exclusion of incidental or consequential damages, so the above warranty may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state.